The Micro MinimOSD is the next evolution of minimization. The Minimosd was engineered to bring users a very powerfull OSD at a unreal cost. After all the community mods, we re-engineered the OSD so every useable pin was easy available.(no more surface soldering) From the manfactures of the WitesSpy KV Team OSD and all your requests have now envoled into the Micro MinimOSD! With all the features of the very popuar WiteSpy KV Team modded OSD but in a 15x15MM size. The only differenece is that It does NOT have the Dc/Dc converter. this means less heat when powered off a Flight controller. The Micro MinimOSD is the same as the older MinimOSD hardware, but has been modified to take advantage of custom firmware options. You can choose firmware that is MAVLink compatible for ArduCopter, or MultiWii Serial compatible for MultiWii and Baseflight/Cleanflight control boards. You can connect two batteries up to 4S so you can see the main flight battery voltage. the second port will allow your FPV battery voltage on the display as well. we also did not forget about the pin for analog or digital PWM RSSI and a connection where you can attach a current sensor. Features: • All the same features as the orignal, but less the half the size • NO Dc/Dc convert . power board via 5 volts • FTDI cable compatible pinout • Standard 6-pin ISP header • Two LED indicators • ATmega328P with Arduino bootloader • MAX7456 monochrome on-screen display • 15x15MM Size! • Modifications for direct connection of two batteries (up to 4S) • Pad for an Analog or Digital PWM RSSI signal • Pad for the connection of a Current Sensor • ATmega328P with Arduino bootloader • Standalone, or with APM/ Flip / Flip32+ flight controllers • These modifications allow direct connection of two batteries (up to 4S) Big thank you to the KV Team and the OSD firmware and the multiwii-osd team This hardware take the hardware mods for this firmware, and builds them into an RTF solution. This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod . FTDI needed to configure and use. This board can be used for any MWC boards or ReadyToFlyer MinimOSD-Extra firmware is wrote by Gábor Zoltán. It's tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as compact as possible. It's main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader, and a MAX7456 monochrome on-screen display. Programming is done through an FTDI card. Specifications ATmega328P with Arduino bootloader MAX7456 monochrome on-screen display FTDI cable compatible pinout Standard 6-pin ISP header Two independent power sections with an LED indicator on each Solder jumpers for combining the power sections +5V 500mA regulator for up to +12V supply input Solder jumper for PAL video option Exposed test points for HSYNC and LOS Dimensions: 0.7"W x 1.7"L (2.4" w/ pins as shown) x 0.3"H MINIMOSD, A MINIMAL ARDUINO-BASED ON-SCREEN DISPLAY BOARD.
Mini osd for Apm2.6 Pixhawk
Description:
On-Screen Display Ardupilot Mega MinimOSD Rev. 1.1 OSD diy drones for APM2 APM2.5 APM2.6 Pixhawk APM has an companion OSD board called MinimOSD. It reads all the MAVLink data in the APM telemetry stream and overlays it on the video stream if you're using an on-board camera and wireless video transmitter. This is useful if you're flying in First Person View (FPV) mode or don't want to use a laptop at the field to see your telemetry data in the Mission Planner.Instructions on connecting and using the MinimOSD board via the APM telemetry port are here. Important note: You cannot connect use the OSD when your APM 2. is also connected via USB (they share the same port). Make sure you disconnect your USB cable from the APM 2 board before attempting to use the OSD.100% Brand New !!!
Complementos Moda
