Item specifics
-
Brand Name
OOTDTY
-
Origin
CN(Origin)
-
Model Number
Solor Controllers
-
Maximum Current
Other
-
Certification
NONE
-
Application
Charger Controller
-
Application
Solar Working Station
Material: Plastic
Color: See Pictures
System Voltage: 6V, 12V
Output Current: 10A
Power Range: ≤60W(6V), ≤120W(12V)
Overload, Short Circuit Protection: Yes
No-load loss: ≤5mA
Charge Loop Drop: ≤0.2V
Disharge Loop Drop: ≤0.1V
Protection Degree: IP30
Working Temperature: -40°~55°
Install and Method of Using:
Firstly, determine the controller output mode , the device factory default setting is normally open mode .if you need to set for the pure light control mode or light control plus timing mode, you need to open the enclosure through set dip switch, changing the discharge mode
When the key set "on" is 1, the key set "off" is 0, normally open, pure light control
Connecting the battery first. if correctly connected, battery indicator will light
Connecting the wire of the solar panel second. if the connection is correct, the indicator light of “charge”will be on or flash 10 seconds later after laying outside under the sun. otherwise, please check the connection
Making sure the solar energy panel is laid outdoors under the sunshine
Connecting the load at the end. if inversely connected, the led lamp may be damaged
Please pay attention to the anode and the cathode to avoid the inverse connection
Size: See the picture
No Retail Package
Quantity: 1 Pc
Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
Package includes:
1 Pc x Auto Solar Panel Charge Controller Battery Charger Regulator New 6V 12V 10A PWM
Description:
- 100% brand new and high quality
- Specification:
- Material: Plastic
- Color:Black
- System Voltage: 6V, 12V
- Output Current: 10A
- Power Range: ≤60W(6V), ≤120W(12V)
- Overload, Short Circuit Protection: Yes
- No-load loss: ≤5mA
- Charge Loop Drop: ≤0.2V
- Disharge Loop Drop: ≤0.1V
- Protection Degree: IP30
- Working Temperature: -40°C~55°C
- Install and Method of Using:
- Firstly, determine the controller output mode , the device factory default setting is normally open mode .if you need to set for the pure light control mode or light control plus timing mode, you need to open the enclosure through set dip switch, changing the discharge mode
- When the key set "on" is 1, the key set "off" is 0, normally open, pure light control
- Connecting the battery first. if correctly connected, battery indicator will light
- Connecting the wire of the solar panel second. if the connection is correct, the indicator light of “charge”will be on or flash 10 seconds later after laying outside under the sun. otherwise, please check the connection
- Making sure the solar energy panel is laid outdoors under the sunshine
- Connecting the load at the end. if inversely connected, the led lamp may be damaged
- Please pay attention to the anode and the cathode to avoid the inverse connection
- Size: See the picture
- No Retail Package
- Quantity: 1 Pc
- Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
Description:
- 100% brand new and high quality
- Specification:
- Material: Plastic
- Color: See Pictures
- System Voltage:12V
- Output Current: 3A
- Working Temperature: -20°C~55°C
- Protection Degree: IP30
- Charge Loop Drop: ≤0.7V
- Disharge Loop Drop: ≤0.1V
- This Solar Charger Controller can automatically manage the work of Solar Panel and battery in solar system
- It's widely used for the solar light on street, garden, park, etc
- Solar charger controller can control the battery recharging automatically and make sure the batteries work longer and safer
- Just working for lead-acid battery‘s charging control
- Equipped with the MCU, artificially controlled
- Equipped with device to avoid the overcharge, over release, electronic short circuit, over loading, battery inversely connecting, solar battery inversely connecting
- The series connection PWM circuit is implemented to form the major charging circuit, make the voltage loss 50% lower than the diode charging circuit, and the charging efficiency 3%-6% higher than the non-PWM
- The LED displayer shows the batteries current situation to make the customer get the information of the batteries
- The controller can automatically identify the voltage of 12V
- The preparation of the conducting wire:calculate the length of the wire ,and then figure out the installation place,make sure the length of the wire is reasonable to decrease the loss of the electricity
- Connect the battery first,pay attention to the anode and the cathode to avoid the inverse connection.the indicator light of the battery willwork if the connection is correct,otherwise,it will not ,but the component of the controller will not be damaged
- Connect the wire of the solar panel, pay attention to the anode and the cathode to avoid the inverse connection
- If the connection is correct,the indicator light of “CHARGE”will be on or flash 10 seconds later after laying outside under the sun,otherwise,please check the connection
- Make sure the solar energy panel is laid outdoors under the sunshine
- Connect the load at the end,pay attention to the anode and the cathode to avoid the inverse connection .if inverse connection ,the led lamp may be damaged
- The batteries has stored much energy,please keep the batteries from the short circuit under any circumstances,we strongly recommend connecting the batteries with the fuse
- Please avoid the short circuit wire and the terminal,for the wire and the terminal may generate voltage two times higher than the rated voltage of the controller
- Please use the insulated tools while operating the controller
- Ensure the children keep away from the battery and the controller
- Size: See the picture
- No Retail Package
- Quantity: 1 Pc
- Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!
|
Complementos Moda